Round Bar

Product Details:

Steels n Metals Division:

• Tool steels & die steels – High Speed Steel, Hot Die Steel, HCHCr, OHNS, 1% Carbon
• Alloy steels – EN Series & AISI Series Steels  
• Stainless steels – SS 202, SS 303, SS 304/304L, SS 316/316L, SS 310, Duplex
• Non ferrous metals –  Brass, Copper, Phosphor Bronze
• Aluminium – 1050, 1100, 2011, 2014, 2017, 3003, 5051, 6061, 6063, 6351, 7039, 7075 grades
• Specialty metals -  Nickel Alloys, Titanium, Hast-alloy, Monal, Inconal
• High manganese steel plates
• Case hardening steels – 16/20MnCr5, SAE 8620, 15CrMo3, 15CrNi6, 18CrNi8
• Carbon steels – C 45, C 50, C 55, C 60, C 65, C 70, C 75, C 80
• Spring steels – EN 9, EN 42J, EN 45, EN 47, EN 48A
• Free cutting steels – EN 1A, EN 8M, EN 15
• Boron steels – all grades
• Boiler quality plates – SA 515/516Gr60-70, DSQ, SAIL MA, En10025, IS:2062
• Steel pipes/tubes – Carbon Steel/Alloy Steel/Stainless Steel
• Flange steels – F 5/F 11/F 12 & F 22 Grades
• Gear blanks & shafting – All Carbon & Alloy Steel grades
• Profile cutting – All Carbon & Alloy Steel Plate Cuttings
• Bhel specn steels – all standard grades

Materials can be supplied:

• Rounds
• Squares
• Hex
• Flats
• Sheets
• Plates
• Pipes
• Wire Rods
• Coils

Product Details:

EN8 engineering steel, also know as 080M40, is an unalloyed medium carbon steel. EN8 is a medium strength steel with good tensile strength. It is suitable for shafts, stressed pins, studs, keys etc. AISI 1040.

Product Details:

Stainless steel is a corrosion-resistant alloy of iron, chromium and, in some cases, nickel and other metals. Completely and infinitely recyclable, stainless steel is the “green material” par excellence. In fact, within the construction sector, its actual recovery rate is close to 100%

Product Details:

D3 steel, also know as 1.2080 (Werkstoff), is an air hardening, high-carbon, high-chromium tool steel. It displays excellent abrasion/wear resistance and has good dimensional stability and high compressive strength. It is heat treatable and will offer a hardness in the range 58-64 HRC.

Product Details:

EN8 is an unalloyed medium carbon steel which is used in applications where better properties than mild steel are required but where the costs do not justify the purchase of a steel alloy. EN8 can be heat treated to provide a good surface hardness and moderate wear resistance by flame or induction hardening processes.

Product Details:

 ST52 SS Round Bar is a type of low alloy steel that is widely used for manufacturing various industrial as well as domestic products and applications.

Product Details:

D2 steel round bar and plate can be used to produce cold work mold with a large cross-section, complex shape, high impact force, and high wear resistance. It also is called DIN 1.2379 and It is a high-carbon and high-chromium cold work mold steel. It is widely used in the world.

Product Details:

EN8 is an unalloyed medium carbon steel grade with reasonable tensile strength. ... EN8 is widely used for applications which require better properties than mild steel but does not justify the costs of an alloy steel. EN8 can be flame or induction hardened to produce a good surface hardness with moderate wear resistance.

Product Details:

Description. C45 grade steel is a medium carbon steel offering moderate tensile strengths. The material is capable of through hardening by quenching and tempering on limited sections but can also be flame or induction hardened to Hrc 55.

Product Details:

D2 ROUND BAR is an air hardening, high-carbon, high-chromium tool steel. It has high wear and abrasion resistant properties. It is heat treatable and will offer a hardness in the range 55-62 HRC, and is machinable in the annealed condition. D2 steel shows little distortion on correct hardening.

Product Details:

C45 grade steel is a C45 Industrial Round Bar The material is capable of through hardening by quenching and tempering on limited sections but can also be flame or induction hardened to Hrc 55.

Product Details:

D2 steel round bar and plate can be used to produce cold work mold with a large cross-section, complex shape, high impact force, and high wear resistance. It also is called DIN 1.2379  It is a high-carbon and high-chromium cold work mold steel. It is widely used in the world.

Product Details:

Mild steel is a type of carbon steel with a low amount of carbon – it is actually also known as “low carbon steel.” Although ranges vary depending on the source, the amount of carbon typically found in mild steel is 0.05% to 0.25% by weight, whereas higher carbon steels are typically described as having a carbon .

Product Details:

Mild steel is a type of carbon steel with a low amount of carbon – it is actually also known as “low carbon steel.” Although ranges vary depending on the source, the amount of carbon typically found in mild steel is 0.05% to 0.25% by weight, whereas higher carbon steels are typically described as having a carbon .

Product Details:

EN8 is an unalloyed medium carbon steel grade with reasonable tensile strength. ... EN8 is widely used for applications which require better properties than mild steel but does not justify the costs of an alloy steel. EN8 can be flame or induction hardened to produce a good surface hardness with moderate wear resistance.

Product Details:

D3/ HCHCR steel is Cold Work Steel with High Carbon High Chromium contents. The Quality with high wear resistant and toughness properties due to Vanadium addition of 0.90% . Normally it supply condition is an Annealed and will offer hardness to reach 57-59 HRC. It can be machinable in the annealed condition.

Product Details:

Mild steel is a type of carbon steel with a low amount of carbon – it is actually also known as “low carbon steel.” Although ranges vary depending on the source, the amount of carbon typically found in mild steel is 0.05% to 0.25% by weight, whereas higher carbon steels are typically described as having a carbon .

Product Details:

P20 Round Steel Bar that is characterized by good toughness at moderate strength levels. The steel is commonly used for plastic injection mold cavities and tooling and for die casting dies for zinc.

Product Details:

P20 Mold Steel is a versatile, low-alloy tool steel that is characterized by good toughness at moderate strength levels. The steel is commonly used for plastic injection mold cavities and tooling and for die casting dies for zinc.

Product Details:

P20 tool steels are nitrided or carburized. These steels are capable of being machined into complex and large dies and molds. P20 steels are mostly used in the carburized condition. The presence of chromium and nickel enhances the toughness and hardness of P20 steels.

Product Details:

D3-HCHCR-WPS steel is Cold Work Steel with High Carbon High Chromium contents. The Quality with high wear resistant and toughness properties due to Vanadium addition of 0.90% . Normally it supply condition is an Annealed and will offer hardness to reach 57-59 HRC. It can be machinable in the annealed condition.

Product Details:

En19 steel is a high quality engineering alloy steel containing chromium and molybdenum. It falls in a class of low alloy steel. It has high fatigue strength, abrasion and impact resistance, toughness, and torsional strength. It can be heat treated in a number of ways to give it a combination of properties.

Product Details:

EN19 is steel alloy which is supplied hardened and tempered. The grade is a nickel chromium molybdenum combination - this offers high tensile steel strength, with good ductility and wear resistance characteristics.

Product Details:

EN31 is a quality high carbon alloy steel which offers a high degree of hardness with compressive strength and abrasion resistance.

Product Details:

EN 47 is a chrome-vanadium based steel, EN 47 can be oil hardened and tempered if required. This process gives the material a good level of abrasion resistance with excellent toughness, these characteristics make it a good choice for applications exposed to stress, shock, and vibration.

Product Details:

20MnCr5 is a case-hardening steel with low carbon content but good hardenability reaching good wear resistance due to high surface hardness after hardening. The small grain size benefits in good ductility and fatigue strength. Suitable for gearboxes and axle gears.

Product Details:

16MnCr5 is an alloyed case hardening steel used for e.g. mechanical engineering components. The steel can be M-treated in order to optimize the machinability.

Product Details:

SAE 8620 Alloy Steel is a low alloy nickel, chromium, molybdenum case hardening steel, generally supplied in the as-rolled condition with a maximum hardness HB 255max. SAE 8620  alloy steel offers high external strength and good internal strength, making it highly wear-resistant. SAE 8620 steel has a higher core strength than grades 8615 and 8617.SAE 8620 alloy steel is flexible during hardening treatments, thus enabling improvement of case/core properties. Prehardened and tempered (uncarbonized) 8620 can be further surface hardened by nitriding but will not respond satisfactorily to flame or induction hardening due to its low carbon content. SAE 8620 alloy steel is suited for applications that require a combination of toughness and wear resistance. This grade is commonly supplied in a round bar. 

Product Details:

SAE 8620 Alloy Steel is a low alloy nickel, chromium, molybdenum case hardening steel, generally supplied in the as-rolled condition with a maximum hardness HB 255max. SAE 8620  alloy steel offers high external strength and good internal strength, making it highly wear-resistant. SAE 8620 steel has a higher core strength than grades 8615 and 8617.SAE 8620 alloy steel is flexible during hardening treatments, thus enabling improvement of case/core properties. Prehardened and tempered (uncarbonized) 8620 can be further surface hardened by nitriding but will not respond satisfactorily to flame or induction hardening due to its low carbon content. SAE 8620 alloy steel is suited for applications that require a combination of toughness and wear resistance. This grade is commonly supplied in a round bar. 

Product Details:

H13 Tool Steel has high hot-wear resistance abilities along with great strength, heat conductivity and invulnerability to hot cracking. It has good resistance to abrasion at each low and high temperature. It displays high level of toughness and ductility.

Product Details:

OHNS is an oil-hardening, non-deforming tool steel which can be hardened at relatively low temperatures. Tools and dies made from O1 will have good wearing qualities since the tungsten and higher chromium content gives improved wear resistance over the straight manganese grades.

Product Details:

M-2 is a tungsten-molybdenum high-speed steel. It is a popular grade for cutting and non-cutting applications. ... In addition, M2 steel has a resistance to decarburization that is characteristic of tungsten types and M2 offers an excellent combination of red hardness, toughness, and wear resistance.

Product Details:

M2 high-speed steel is a tungsten-molybdenum tool steel. M2 is characterised by well-balanced toughness, wear resistance and red hardness properties. ... M2 is medium-alloyed and is a good all-round performer with good machinability, in this respect it is superior to the high alloyed cold work steels.

Product Details:

SAE 8620 round bar offered by steel mart is from prime manufacturers & has zero rejections. Steel mart firmly believes in catering to the needs of the customers by way of supplying genuine – tested materials at extremely reasonable rates. Steel mart is an ISO 9001:2008 certified company which reflects the quality consciousness of the boss & staff members. Steel mart is in a position to supply all kinds of steels n metals in round, square, flat, sheet, plate, coil sections and holds approx 900 m/t to 1000 m/t stocks of the materials in various go-downs & warehouses. Steel mart specializes in the supply of:- en 100 alloy  steel round bars. SAE 8620 round bar can be supplied in size ranging from 4mm dia to 200mm dia. SAE 8620 round bar are supplied by us to various industries.

Product Details:

C45 grade steel is a medium carbon steel offering moderate tensile strengths. The material is capable of through hardening by quenching and tempering on limited sections but can also be flame or induction hardened to Hrc 55.

Product Details:

EN36 is a carburising steel grade with very high surface strength with a soft but strong core. The material retains a remarkable degree of toughness. With high tensile strength, EN36 is used in the production of numerous high strength parts including crankshafts in the automotive and aerospace sector.

Product Details:

En 353 steel has a carbon content of 0.17% and the commonest form of steel as it provides material properties that are acceptable for several automobile applications such as significant duty gear, shaft, pinion, camshafts and gudgeon pins.

Product Details:

Tool Steel H11 has minimal distortion during deep-hardening and air-hardening thanks to the balanced alloy content.
...

Product Details:

H13 Tool Steel has high hot-wear resistance abilities along with great strength, heat conductivity and invulnerability to hot cracking. It has good resistance to abrasion at each low and high temperature. It displays high level of toughness and ductility.

Product Details:

M-2 is a tungsten-molybdenum high-speed steel. It is a popular grade for cutting and non-cutting applications. ... In addition, M2 steel has a resistance to decarburization that is characteristic of tungsten types and M2 offers an excellent combination of red hardness, toughness, and wear resistance.